Your cart is currently empty!
Art.nr: 5907761103337
AC deep well pump 4″ 4SD 5-20, 2,2KW, 400Volt
fr. 735,54 €
Suitable for boreholes at a maximum of 95 meters water level with large flow, e.g. to several houses.
Dimension the maximum pressure (head) required by the pump
Pressure at the tap (max. pressure): 3 bar = 30 meters
Pressure loss from friction in pipes and couplings: approx. 5 meters
Static head (lowest level of the water surface in the well to the top tapping point) = meters
The sum of the heights must always be lower than the maximum head by a wide margin.
The pump diameter is 100mm and requires at least 115mm inner diameter of the casing
An advantage of this pump is that it can be easily separated into two parts, the electric motor and the pump part.
This means that if the pump’s electric motor or pump part breaks down, you can just replace that part and save money.
Those who have bad water that wears out the pump part a lot can have one in reserve at home for quick replacement at lower cost.
Submersible pump 4SD with 1-phase or 3-phase from the manufacturer Omnigena, is a 4″ multistage pump for pumping clean and cold water.
The pump can be used in a wide range of applications, both at home and in the industrial, agricultural and horticultural sectors.
The pump can be used for drinking water systems, irrigation systems and industry.
4 SD pump is resistant to corrosion and mechanical damage. Shaft, coupling, cable cover, inlet screen are made of stainless steel, impeller and diffusers are made of wear-resistant noryl, and the supply and suction ports are made of brass.
The pump works in all, even difficult working conditions. It is adapted for continuous and intermittent operation.
The pump should not pump water with solid abrasive particles, the design of the 4SDM and 4SD pumps allows pumping water with a sand content of up to 5%.
The unit is energy-efficient, quiet, easy to install and operate.
The unit is very efficient. It pumps up to 150 l/min and the maximum lifting height is 115 meters.
There is a valve inside the pump, but this is not a check valve but an anti-sand return valve and protects the hydraulic part from returning sand from the pipeline.
Engine cover included
We always recommend using the accompanying overload protection to protect the pump motor.
This cover should be installed in a dry place, not necessarily inside the building, but it cannot be exposed to moisture.
May need to be purchased for
- Pem slang
- Drill cap, cover for the borehole to protect against contamination
- Lifting cables and clamps
- Single adapter for connecting the pump to the feed pipe
Connection on the outlet is internal thread R50, 2 inches.
It includes check valve
The length of the pump cable included is 20 meters unless you buy a pre-spliced power cable.
Select if you want a pre-spliced drinking water approved power cable in the most common length above the buy button.
If other lengths are desired, it can be ordered against longer delivery time.
Technical data
Max capacity: 150 l/min.
Max lifting height: 130 m.
Motor power: 2.2 kW.
Voltage: 400V.
Outlet: Female thread R50 (2″)
Height: 1366 mm.
Pump diameter: 100 mm
Weight 23 kg, without cable
Max water temperature: 35°C.
Degree of protection: IP 68.
Winding insulation class: B.
Number of starts up to [x/hour]: 20.
Minimum cooling flow for the motor: 0.08 m/s.
Working position: vertical.
Materials:
Pump casing: stainless steel.
Cable sheath: stainless steel.
Pump shaft: stainless steel.
Impellers and diffusers: noryl.
Inlet strainer: stainless steel.
Outlet: brass.
Suction body: brass.
Product details
Article number:
5907761103337
Brand:
Avloppscenter (AC)
Length of cable:
AC deep well pump 4" 4SD 5-20, 2,2KW, 400Volt, 20m cable | AC deep well pump 4" 4SD 5-20, 2,2KW, 400Volt, 95 cable
Suitable for boreholes at a maximum of 95 meters water level with large flow, e.g. to several houses.
Dimension the maximum pressure (head) required by the pump
Pressure at the tap (max. pressure): 3 bar = 30 meters
Pressure loss from friction in pipes and couplings: approx. 5 meters
Static head (lowest level of the water surface in the well to the top tapping point) = meters
The sum of the heights must always be lower than the maximum head by a wide margin.
The pump diameter is 100mm and requires at least 115mm inner diameter of the casing
An advantage of this pump is that it can be easily separated into two parts, the electric motor and the pump part.
This means that if the pump’s electric motor or pump part breaks down, you can just replace that part and save money.
Those who have bad water that wears out the pump part a lot can have one in reserve at home for quick replacement at lower cost.
Submersible pump 4SD with 1-phase or 3-phase from the manufacturer Omnigena, is a 4″ multistage pump for pumping clean and cold water.
The pump can be used in a wide range of applications, both at home and in the industrial, agricultural and horticultural sectors.
The pump can be used for drinking water systems, irrigation systems and industry.
4 SD pump is resistant to corrosion and mechanical damage. Shaft, coupling, cable cover, inlet screen are made of stainless steel, impeller and diffusers are made of wear-resistant noryl, and the supply and suction ports are made of brass.
The pump works in all, even difficult working conditions. It is adapted for continuous and intermittent operation.
The pump should not pump water with solid abrasive particles, the design of the 4SDM and 4SD pumps allows pumping water with a sand content of up to 5%.
The unit is energy-efficient, quiet, easy to install and operate.
The unit is very efficient. It pumps up to 150 l/min and the maximum lifting height is 115 meters.
There is a valve inside the pump, but this is not a check valve but an anti-sand return valve and protects the hydraulic part from returning sand from the pipeline.
Engine cover included
We always recommend using the accompanying overload protection to protect the pump motor.
This cover should be installed in a dry place, not necessarily inside the building, but it cannot be exposed to moisture.
May need to be purchased for
- Pem slang
- Drill cap, cover for the borehole to protect against contamination
- Lifting cables and clamps
- Single adapter for connecting the pump to the feed pipe
Connection on the outlet is internal thread R50, 2 inches.
It includes check valve
The length of the pump cable included is 20 meters unless you buy a pre-spliced power cable.
Select if you want a pre-spliced drinking water approved power cable in the most common length above the buy button.
If other lengths are desired, it can be ordered against longer delivery time.
Technical data
Max capacity: 150 l/min.
Max lifting height: 130 m.
Motor power: 2.2 kW.
Voltage: 400V.
Outlet: Female thread R50 (2″)
Height: 1366 mm.
Pump diameter: 100 mm
Weight 23 kg, without cable
Max water temperature: 35°C.
Degree of protection: IP 68.
Winding insulation class: B.
Number of starts up to [x/hour]: 20.
Minimum cooling flow for the motor: 0.08 m/s.
Working position: vertical.
Materials:
Pump casing: stainless steel.
Cable sheath: stainless steel.
Pump shaft: stainless steel.
Impellers and diffusers: noryl.
Inlet strainer: stainless steel.
Outlet: brass.
Suction body: brass.
Article number:
5907761103337
Brand:
Avloppscenter (AC)
Length of cable:
AC deep well pump 4" 4SD 5-20, 2,2KW, 400Volt, 20m cable | AC deep well pump 4" 4SD 5-20, 2,2KW, 400Volt, 95 cable